PBN

SFP-FE/GExxxx-SC/LC PC

100Mbps/1Gbps Single-Mode SFP DDM Transceiver

SFP-FE/GExxxx-SC/LC PC

About the Product

PBN’s DDM SFP transceivers are designed for medium-haul operations up to 80 km using a single-mode fiber. The transceivers feature a 1310 nm, 1490 nm or 1550 nm laser transmitter and a PIN photodetector for highest reliability.
The optical output can be disabled using either a TTL logic-high signal, or via the I2C bus. Transmitter-fault indication and loss-of-signal output indication are also provided, using discrete status lines.
Digital diagnostics functions are also available through an I2C bus based on the popular SFP MSA to achieve highest vendor compatibility.

  • Up to 1 Gbps fiber data-rate 
  • 1310 nm, 1490 nm or 1550 nm laser transmitter 
  • SFP MSA compliant 
  • PIN photo-detector 
  • Up to 80 km on 9/125 μm single-mode fiber 
  • Hot-pluggable SFP footprint 
  • BIDI SC/UPC type pluggable optical interface 
  • Low power dissipation
  • Metal enclosure, for lower EMI
  • RoHS compliant and lead-free
  • Single +3.3 V power supply
  • Supports Digital Diagnostic Monitoring (DDM) interface
  • Compliant with SFF-8472
  • Case operating temperature range: 0 o C to +70 o C
 

Applications

  • Switch-to-switch interface
  • Fast / Gigabit Ethernet interconnections
  • Switched backplane applications
  • Router/server interface
  • Customer Premise last mile link

Diagonostics

  • Transceiver temperature
  • Laser bias current
  • Optical transmit powe
  • Optical receive power
  • Transceiver supply voltage 

Absolute maximum ratings

Supply voltage (Vcc) Minimum -0.5 V, maximum +4.0 V
Signal input voltage Minimum -0.3 V, maximum + 0.3 V
Receiver damage threshold Minimum 5 dBm
Storage temperature (TS) Minimum -40 °C, maximum +85 °C
Storage ambient humidity Minimum 5 %, maximum 95 % (non-condensing)

Recommended operating conditions

Case operating temperature Minimum 0 °C, maximum +70 °C
Ambient humidity Minimum 5 %, maximum 70 % (non-condensing)
Supply voltage Minimum +3.13 V, maximum +3.47 V, typical +3.3 V
Supply current Maximum 280 mA
Power supply noise rejection Maximum 100 mV p-p (100 Hz to 1 MHz)
Data rate Tx / Rx 1 Gbps / 1 Gbps
Transmission distance 20 km / 80 km
Coupled fiber 9/125 μm single-mode fiber

Electrical characteristics

Transmitter:

Supply current (Icc)

Maximum A mA (1)

Trans. disable input-high (VDISH)

Minimum 2 V, maximum Vcc + 0.3 V

Trans. disable input-low (VDISL)

Minimum 0 V, maximum 0.8 V

Trans. fault input-high (VTxFH)

Minimum 2 V, maximum Vcc + 0.3 V

Trans. fault input-low (VTxFL)

Minimum 0 V, maximum 0.8 V
Receiver:

Supply current (Icc)

Maximum B mA (1)

LOSS output voltage-high (VLOSH)

Minimum 2 V, maximum Vcc + 0.3 V (LVTTL)

LOSS output voltage-low (VLOSL)

Minimum 0 V, maximum 0.8 V (LVTTL)

Optical characteristics

Transmitter:

Average output power

Minimum -9 dBm, maximum -3 dBm

Extinction ratio

Minimum 9 dB

Nominal optical wavelength ( λ )

1310 nm, 1490 nm or 1550 nm

Spectrum width (RMS)

Maximum 3.5 nm (Tx = 1310 nm)

Side mode support ratio (SMSR)

Minimum 30 dB (Tx = 1310nm/1490 nm/1550nm)

Spectrum bandwidth (-20 dB)

Maximum 1 nm (Tx = 1490 nm)

Transmitter OFF output power

Maximum -45 dBm

Diff. line input impedance (RIN)

Minimum 90 Ohm, maximum 110 Ohm, typical 100 Ohm

Total jitter (peak-peak)

Maximum 0.1 UI (measured at 2^7-1 NRZ PRBS pattern)

Output eye mask

Compliant with IEEE802.3z (class 1 laser safety) (Transmitter eye mask definition)
Receiver:

Wavelength (λIN)

1310 nm or 1490 nm

Sensitivity (PiN)

Maximum -20 dBm (2)

Input sat. power (overload) (PSAT)

Minimum -3 dBm

Loss of signal assert (PA)

Minimum -38 dBm

Loss of signal de-assert (PD)

Maximum -22 dBm (3)

LOS hysteresis (PA - PD)

Minimum 0.5 dB, maximum 6 dB, typical 2 dB
Regulatory compliance
Electrostatic discharge (ESD)

IEC/EN 61000-4-2 compliant

Electromagnetic interference (EMI) FCC Part 15 Class B EN 55022 Class B (CISPR 22A) compliant
Laser eye safety FDA 21CFR 1040.10, 1040.11 IEC/EN 60825-1, 2 Class 1 laser product
Component recognition IEC/EN 60950, UL compliant
RoHS 2002/95/EC compliant
EMC EN61000-3 compliant

Notes

(1) A (TX) + B (RX) = 280 mA (not including termination circuit).

(2) Measured with light source (1310 nm or1490 nm), ER = 9 dB; BER =< 10^-12 @ PRBS = 2^7-1 NRZ.

(3) When loss of signal is de-asserted, the RX data +/- output is the signal output.

* Subject to change without further notice.

SFP-FE4931-LCPC

SFP plug-in, 100 Mbps, 20 km, TX = 1490 nm, RX = 1310 nm, LC/PC blue - CP110 compatible

SFP-FE4931-SCPC

SFP plug-in, 100 Mbps, 20 km, TX = 1490 nm, RX = 1310 nm, SC/PC blue - CP110 compatible

SFP-FE5531-LCPC

SFP plug-in, 100 Mbps, 20 km, TX = 1550 nm, RX = 1310 nm, LC/PC blue

SFP-FE5531-SCPC

SFP plug-in, 100 Mbps, 20 km, TX = 1550 nm, RX = 1310 nm, SC/PC blue

SFP-GE4931-LCPC

SFP plug-in, 1 Gbps, 20 km, TX = 1490 nm, RX = 1310 nm, LC/PC blue - CP120 compatible

SFP-GE4931-SCPC

SFP plug-in, 1 Gbps, 20 km, TX = 1490 nm, RX = 1310 nm, SC/PC blue - CP120 compatible

SFP-GE3149-LCPC

SFP plug-in, 1 Gbps, 20 km, TX = 1310 nm, RX = 1490 nm, LC/PC blue

SFP-GE3149-SCPC

SFP plug-in, 1 Gbps, 20 km, TX = 1310 nm, RX = 1490 nm, SC/PC blue

SFP-GE4955-80KM-LCPC

SFP plug-in, 1 Gbps, 80 km, TX = 1490 nm, RX = 1550 nm, LC/PC blue

SFP-GE5549-80KM-LCPC

SFP plug-in, 1 Gbps, 80 km, TX = 1550 nm, RX = 1490 nm, LC/PC blue

SFP-GE-COPPER

SFP Plug-in,1Gbps,RJ45 Copper Transceiver

SFP-EPON-20-SCPC

SFP Plug-in,GEPON,1.25Gbps,1490TX/1310RX,SC/PC Blue

  • SFP-FE/GE xxxx-SC/LC PC